RSSArc furnace that melts anything
Handy for arc experiments, Popular Science 1933
HEAT so terrific that no known substance is able to withstand it for long can be developed in your home laboratory with nothing more than a pair of electric light carbons, a small crucible, and some means of controlling the flow of the electric current from the house mains through the arc.Most electrical experimenters attempt to use an old toaster or electric grill in series with the arc. This works all right, but the current flow is limited to three or four amperes and is greatest when the carbons are in contact and the arc is producing the least amount of heat. Adding another toaster or grill in parallel with the first one doubles the current through the arc, doubles the cost of operation, and still is open to the objection that the current flow is greatest when the arc is least effective.
The difficulty is that a carbon arc, operating on the ordinary 60-cycle, 110-volt current, actually requires only about 35 volts. The difference is wasted in useless heat from the grill or toaster.
Modern Mechanix ยป EXPERIMENTAL Arc Furnace MELTS ANYTHING - Link.
Posted by Phillip Torrone |
Mar 20, 2007 03:00 PM
DIY Projects, Electronics, Modern Mechanix |
Permalink
| Comments (7)
Recent Entries
- Gifts - for Makers who like blimps
- $5 Motorcycle camera mount
- Plate mail butchers apron outfit...
- A free view of the world -- OpenAerialMap
- MAKE - Metro @ PULSTV
- Lab-on-a-Chip with Shrinky Dink and toaster oven
- Myvu Solo goggles take apart...
- Spiral Star art made in Excel
- MAME oscilloscope
- HOW TO - Make Fimo fractals
Comments
Oldest comments listed first.
I did this using a cheap $59 arc welder from homier. I used carbon gouging rods (used for cutting metal thats too thick for a plasma torches or gas torches) for the electrodes. Instead of a crucible I used two bricks that I hollowed out with an air hammer to hold the molten metal. The bottom has large area hollowed out to contain the molten metal. The other one is a lid with two channels for the electrodes. Its got to be about the cheapest way to melt metal for small castings. Without the lid I wasn't able to get the metal hot enough to pour into a mold thou. This is very dangerous and life threatening by the way. It has the potential to cause blindness, electrocution, burns,... to many ways to kill or permanently mame yourself doing this to list. Some things to note about this are the cheapo arc welder listed above came with a 220 volt euro plug that I had to cut off and rewire. I run it at its lowest (45 amp) setting for the greatest duty cycle(I wired it up to 110 once and it ran cranked all the way up to the 100 amp setting without the thermal protection tripping). The smallest carbon rods I found work best (1/4 inch). It also seem to help if I sharpen them and cut the copper coating off from the ends that are arcing. The carbons are kind of hard to find. I found them at the local farm and fleet store. My normal welding supplier did not carry them. The bricks do crack open after a while and drop the molten metal out so don't do this on a table while wearing flip-flops. My metal of choice so far has been rusty nails for small casts to turn in my lathe. All the rust seems to get pushed out of the molten metal and the castings seem to be good all the way through as far as I can tell. This is sort of a micro scale version of the way scrap steel is melted back down.
Did one similar to this when I was 13 from a 1940s chemistry book...
Used a saltwater rheostat ; 2 lead sinkers in a petri dish with salt water!!
An old flower pot and carbons from some really old batteries.
Blew the fusebox a bunch of times, and my eyes still hurt! Heh.
Subscribe to MAKE Magazine!
Subscribe today, save 42% and get web access to MAKE free. MAKE Digital Edition is available only to subscribers.
$34.95 / 1 year
(4 Quarterly Issues)
Happy holidays from MAKE!
Open source hardware gift guide!
Looking to give gifts this year that are open source? Here's our "Open Source Hardware" gift guide. Open source 3D printers, TV-turn-off devices, iPod chargers, music players, Wi-Fi companions, educational electronic kits and more. Each of the kits, projects and open source hardware gifts in this guide represents more than just a holiday gift, it's a chance to support this nascent open hardware movement - Link.
Books for Makers - A gift guide of lost arts and new tech
If you like MAKE and the things we celebrate you'll like these books, we've picked out some "lost arts" books like chainsaw art and soap box derby construction, along with more updated tech like astronomy. They make great gifts for the holidays! - Link.
Arduino gift guide - Give the gift of learning electronics!
Arduino is a tool for making computers that can sense and control more of the physical world than your desktop computer. It's an open- source physical computing platform based on a simple microcontroller board, and a development environment for writing software for the board, open source and a great gift! - Link.
MAKE Magazine gift subscription
The first magazine devoted to digital projects, hardware hacks, and D.I.Y. inspiration. MAKE brings the do-it-yourself mindset to all the technology in your life. Give the gift of MAKE that will be enjoyed all year long with a gift subscription! - Link (use code CMAKE for $5 off USD).
Maker store gift certificate
Give your favorite maker a gift certificate good for anything from the Maker Store! You'll enter the amount and delivery method after you add to to your cart in the Maker store - Link.
Phillip Torrone
Senior Editor
Tel: 707-827-7311
Gareth Branwyn
Robot Maker
Jonah Brucker-Cohen
Researcher
Natalie Zee Drieu
Bre Pettis
Current Podcast
Make a Repstrap (Part 2) - Weekend Projects Podcast
MP4 | Hi-Def | Blip | Youtube | PDF | Subscribe In this Weekend Projects podcast I'll walk you through the different parts of the hardware on the reprap. You'll want to take a look at the pdf for...
More...
